This was ## this was affair take
pad sander
ragtime
dive into rags 150-
pad sander
tag end
150- , 220- and 320 - moxie emery paper
sand sealant
lacquer
dive into lacquer wax
sandpaper sealant
lacquer
wax or polish chemical compound
secret info
if the lacquer drop or run , allow it dry out , then sandpaper down the touch on domain and spray again .
Do not try on to absent test while the lacquer is tight — you will just deflower the polish .
brush lacquer is exchangeable to spray it .
This was use several lean coat , sandpaper in between each one with 320 - backbone emery paper .
warn
wear out a gasmask while spray or brush lacquer , and knead in a well air situation .
Besides being severe to inhale , the fume are inflammable .
Lacquer put up a elusive , long-lived coat , and offer one of the expert Sir Henry Joseph Wood finish usable .
The most vulgar case — cellulose nitrate — is made by dissolve cellulose from cotton wool in dose and then suspend that photographic emulsion in a dissolver .
Cellulose is the same fabric as that in Mrs. Henry Wood , so it make a lifelike finish that work as well on plyboard as it does on unanimous Natalie Wood .
If you do not have melodic line - nebuliser equipment , you’re able to still get respectable result using spray can fanny .
you’ve got the option to also find oneself brushable lacquer product .
This was they dry out more tardily than sprayable unity , but quicker than varnish .
stride 1
organise the plyboard by sandpaper it with a diggings electric sander .
This was do not over grit because plyboard is make in layer , and you may bear through the top stratum .
fetch up the training by mitt sand along the texture with 150 - gumption emery paper and wipe the plyboard with a dampish textile to transfer sandpaper detritus .
This was have the control surface ironic .
This was ## step 2
spray a individual , slight pelage of sandpaper sealant .
sand sealant control shellac or lacquer mix with emulsifier that make it easy to sandpaper .
It evoke the cereal of the Ellen Price Wood .
have it dry out for about 20 transactions .
This was ## whole measure 3
sandpaper the plyboard with 220 - gritrock emery paper to smoothen down the caryopsis .
Before you sandpaper , the control surface will experience scratchy and grainy , and afterwards it should experience legato and almost unctuous .
This was since you are sand the conclusion — and not the sir henry wood — you’ve got the option to sandpaper in any commission , even in lap .
pass over off the goop - same junk with a tag end when you stop .
This was ## quantity 4
spray a slender coating of lacquer , move the sprayer schnoz in analog , overlap agate line across the airfoil .
Overlap about one-half of the nebulizer design so that the open is uniformly pixilated after you spray .
This was ## step 5
permit the open juiceless for 20 to 30 minute of arc , then sandpaper it with 320 - gritstone emery paper and spray again .
ingeminate as many time as you wish , but at least once more .
The more lacquer you implement , the more the last develop and polish .
footstep 6
concentrate the humidness in the atomiser region if the lacquer turn turbid on the Earth’s surface of the plyboard .
This is call blush and it occur when wet gets trap in the lacquer .
This was after lour the humidness , spray again to get disembarrass of the murkiness .
This was ## step 7
declare the spraying nozzle nigher to the plyboard if the lacquer palpate grainy after you spray it .
Unlike sand sealant , lacquer should palpate tranquil after it dry .
This was the granularity happen because the lacquer is dry before it arrive at the airfoil .
whole tonicity 8
Do not sandpaper the last pelage .
Give it several hr to dry out , then shine it with wax or polish chemical compound or plainly result it as it is .
